osha.gov

Comply with OSHA 1910.94(a) ventilation and respirator requirements for abrasive blasting

Confirm OSHA fall-protection and equipment requirements before authorizing stilt use on a drywall job

Mitigate material handling and ergonomic hazards when hanging drywall

Prepare a woodworking shop for an OSHA Combustible Dust National Emphasis Program inspection

Bring shop table saws and woodworking machinery into compliance with OSHA 29 CFR 1910.213

Confirm bucket-truck operators are properly trained before an aerial sign install

Comply with OSHA exposure limits when installing fiberglass or mineral wool insulation

Determine whether OSHA Subpart R (steel erection) or another 1926 subpart governs a specific activity on a project combining precast/tilt-up concrete and structural steel

Apply OSHA basics to in-home appliance service work

Set up and execute a multiple-lift ('Christmas tree') rigging operation in compliance with OSHA 1926.753(e)

Determine approval and notification requirements before repairing, replacing, or field-modifying anchor rods (anchor bolts) on a steel erection project

Verify connector training and qualification requirements are met before assigning ironworkers to connector duties under 1926.761

Verify signal person qualification documentation required by OSHA 1926.1428 before hand-signaling crane picks on a steel erection site

Apply OSHA Table 1 silica controls when cutting fiber-cement siding

Confirm a crane operator meets OSHA's certification and evaluation requirements under 1926.1427 before operating on a steel erection project

Comply with OSHA's structural steel assembly and metal decking hole/opening rules under 1926.754 during deck installation

Apply OSHA's double-connection (clipped connection) requirements when two members share common bolt holes at a column or beam-over-column

Plan safe scaffold and mortar-board access for a lath/plaster crew on a multi-story stucco project

Install perimeter safety cables on a multi-story steel structure in compliance with OSHA 1926.760(a)

Ensure a suspension scaffold's counterweight/outrigger system meets OSHA's stability requirement

Determine when a qualified rigger is required for hoisting activities on a steel erection project and how to document that qualification

Follow OSHA's field-bolting and bridging restrictions for open web steel joist erection under 1926.757

Assemble the written notifications and documentation a controlling contractor should have on hand to demonstrate Subpart R compliance during an OSHA inspection or internal audit

Apply OSHA's temporary bracing and plumbing-up requirements before removing bracing during structural steel assembly under 1926.754

Confirm pre-erection site conditions and required written notifications before starting structural steel erection under OSHA 1926.752

Determine the correct fall protection approach when connectors use an aerial lift versus climbing/working directly off the steel during erection

Apply OSHA's tiered fall-protection thresholds for steel erection activities, connectors, and controlled decking zones under 1926.760

Apply OSHA power-line clearance rules when transporting and operating a drilling rig mast

Determine when high winds require adjusting or suspending crane operations during steel erection under 1926.1417

Verify column anchorage design meets the minimum anchor rod and setting requirements of OSHA 1926.755(a) before steel erection

Verify Crane/Attachment Operator Certification for Demolition Work

Comply with OSHA Chute (1926.852) and Wall Stability (1926.854) Rules

Determine When a PE-Stamped Engineered Demolition Plan Is Required

Ensure wood-chipper operation meets safety compliance requirements

Apply the correct OSHA crane rules to a crane-assisted tree removal

Qualify a line-clearance arborist and apply minimum approach distances under OSHA 1910.269

Verify Utility Disconnects Before Starting Structural Demolition

Apply fall protection and load limits for roof snow removal

Keep pedestrians safe around skid steers and loaders on sidewalks

Plan Safe High-Reach Excavator Demolition Operations

Determine which OSHA standards apply to a tree-trimming job

Achieve OSHA HazCom (1910.1200) SDS compliance for cleaning chemicals used by a BSC

Apply OSHA 1926.1153 Table 1 controls for handheld grinders used for mortar removal (tuckpointing)

Apply OSHA 1926.1153 Table 1 controls for saws used to cut brick, block, or stone during masonry repair

Implement GHS-compliant secondary-container labeling for diluted cleaning chemicals

Build an OSHA Bloodborne Pathogens (1910.1030) exposure control plan for custodial staff

Determine whether a temporary support structure is regulated as a scaffold under 1926 Subpart L or as shoring/formwork under 1926 Subpart Q before applying compliance requirements

Run a documented daily pre-shift scaffold inspection program by a competent person that satisfies OSHA 1926.451(f)(3)

Apply GHS-compliant labeling to secondary/diluted cleaning-chemical containers under OSHA HazCom

Erect a tube-and-coupler scaffold to meet OSHA 1926.452(b), including when a registered professional engineer's design is required

Store and handle pool chemicals safely on a service route and at a facility, keeping incompatible chemicals segregated

Erect a pump jack scaffold to meet OSHA 1926.452(j) bracket, pole, and bracing requirements

Determine who must serve as the OSHA-required competent person versus qualified person on a 1926.451 scaffold job and what each role must do

Determine which OSHA 1926 Subpart L scaffold rules apply before starting a supported frame scaffold job on a construction site

Apply current OSHA fall protection requirements (29 CFR 1926.501(b)(13)) for residential steep-slope roofing work performed 6 feet or more above a lower level.

Set up a ladder jack scaffold within OSHA's 1926.452(k) height limit and ladder-support requirements

Build a compliant scaffold platform under 1926.451(b) covering planking span, overlap, and gap limits

Set up a two-point adjustable suspension scaffold (swing stage) to meet OSHA 1926.452(p) and the related 1926.451(d) tieback and outrigger criteria

Implement OSHA-compliant silica dust controls for a tuckpointing crew using handheld grinders for mortar removal, per 29 CFR 1926.1153 Table 1

Build an OSHA Bloodborne Pathogens (29 CFR 1910.1030) exposure control plan for a custodial crew

Bring janitorial chemical SDS/labeling into compliance with OSHA HazCom (29 CFR 1910.1200) during the GHS Revision 7 transition

Erect a system or modular scaffold, such as cuplock or ringlock, in compliance with both the manufacturer's instructions and OSHA 1926.451

Select and implement the correct OSHA 1926.451(g) fall protection method for each scaffold type on the job above the 10-foot threshold

Apply OSHA's feasibility exception for fall protection during scaffold erection and dismantling under 1926.451(g)(2)

Provide OSHA-compliant access to scaffold platforms under 1926.451(e) whenever the platform is more than 2 feet above or below the access point

Decide whether it is safe to work on or erect a scaffold under wind, storm, or icy conditions per OSHA 1926.451(f)

Maintain OSHA-required minimum clearance distances between a scaffold and nearby power lines under 1926.451(f)(6)

Verify outrigger beam and counterweight calculations for a suspended scaffold meet OSHA's tipping-moment and material requirements before hanging the rig

Set up ladders and roof brackets (slide guards) safely for steep-slope work while ensuring the overall fall-protection approach meets current OSHA requirements.

Configure and safely move a rolling (mobile/Baker-type) scaffold in compliance with OSHA 1926.452(w), including the employee-riding restrictions

Apply OSHA 1926.1413 wire rope removal criteria during a running-rope inspection performed by a third-party inspection company

Scope an operational-aid/load-moment-indicator (LMI) calibration check as part of a crane inspection company's annual comprehensive inspection under OSHA 1926.1416/1417

Identify the documentation and retention requirements a crane inspection company must meet after a 1926.1412 monthly or annual inspection

Scope annual proof-load testing requirements for cranes and derricks that a third-party inspection company may be asked to perform or witness

Handle a customer or insurer contractual requirement for inspector qualifications that exceeds OSHA/ASME minimums, without overstating what public regulation itself mandates

Set up compliant vacuum/suction-cup lifting procedures for glass handling under OSHA and ASME B30.20

Apply OSHA 1926.501(b)(10) fall protection requirements for low-slope roofing work

Determine which OSHA 1926.1412 inspection category (shift, monthly, or annual/comprehensive) a crane inspection company's engagement falls under and what deliverable each category requires

Confirm post-assembly inspection obligations under OSHA 1926.1404 and 1926.1412(c) for an inspection company verifying a newly assembled crane before first use

Apply OSHA 1926.1412's special inspection triggers (idle equipment, severe service/severe weather exposure) that a crane inspection company must recognize outside the routine shift/monthly/annual cycle

Determine when an articulating/knuckle-boom crane loses its OSHA 1926.1400(c) exemption and requires full Subpart CC inspection and certified-operator compliance

Distinguish 'qualified person' from 'competent person' under OSHA 1926.1401 when scoping who at an inspection company can sign off on which inspection tier

Apply OSHA 1926.1436 derrick inspection and load-test requirements for an inspection company servicing derrick equipment (as distinct from cranes)

Determine when equipment modifications under OSHA 1926.1434 require a follow-up inspection by a qualified person before a crane returns to service

Outline a rack safety training program for warehouse staff, distinguishing forklift-operator training from general pedestrian/order-picker training.

Design a forklift-rack-impact reporting policy for a warehouse, covering what to report, when, and to whom.

Explain OSHA's actual regulatory authority over industrial storage racks, being explicit that there is no OSHA standard dedicated to rack design or anchoring.

Select scaffold plank lumber for a sign-installation scaffold using the correct OSHA/ANSI span basis, avoiding tank-builder-scaffold misapplication

Confirm OSHA touchpoints for crane and bucket-truck (aerial lift) use during sign installation

Determine temporary construction-fence requirements for site security, distinguishing genuine OSHA obligations from local-ordinance practice.

Perform and document the monthly wire rope inspection required under 29 CFR 1926.1413

Verify the load-chart and rated-capacity duties a crane operator must follow under 29 CFR 1926.1417

Determine the required power line clearance under 29 CFR 1926.1408 (Table A) before operating equipment near energized lines

Set up compliant crane-suspended personnel platform (man-basket) operations under 29 CFR 1926.1431

Determine which signal person qualification method satisfies 29 CFR 1926.1428 for a given job

Perform and document the OSHA-required annual and monthly (frequent) crane inspections under 29 CFR 1926.1412

Determine who qualifies as the 'qualified person' or 'competent person' for crane inspections under Subpart CC

Determine whether OSHA's crane operator certification requirement (29 CFR 1926 Subpart CC / 1926.1427) applies to a given job and what documentation it requires

Determine whether a piece of construction lifting equipment is regulated as a 'derrick' or a 'crane' under Subpart CC and what that means for compliance

Identify what PPE and glass-handling practices OSHA expects for a glazing crew handling large panes (cut/laceration hazard), since there is no glazing-specific OSHA standard.

Determine what OSHA fall-protection requirements apply to workers installing curtain wall or window glazing at height on a commercial job site.

Build a rooftop snow-removal safety checklist for a commercial crew this winter, grounded in OSHA's published hazard alert.

Help a contractor compare ice-melt products' chloride content and environmental impact using manufacturer Safety Data Sheets (SDS) rather than marketing claims.

Confirm OSHA confined-space obligations for septic tank entry and vacuum truck tank work

Verify whether OSHA federally mandates a color-coded scaffold tagging system (e.g., green/yellow/red) before telling a contractor it's a legal requirement.

Look up OSHA's general scaffold fall-protection and guardrail thresholds under 29 CFR 1926.451 for a specific platform height.

Pull the type-specific bracing and height-limit rules for tube-and-coupler or fabricated-frame scaffolds from 29 CFR 1926.452.

Determine whether a designated worker meets OSHA's 'competent person' bar for scaffold work under 29 CFR 1926 Subpart L.

Check whether a countertop fabrication shop falls within OSHA's ongoing enforcement focus on engineered stone silica exposure before a compliance self-audit.

Confirm OSHA's scaffold employee-training requirements under 29 CFR 1926.454, including retraining triggers.

Confirm a stationary countertop fabrication shop's obligations under OSHA's general industry respirable crystalline silica standard (29 CFR 1910.1053) rather than the construction standard.

Determine whether OSHA's Logging Operations standard (29 CFR 1910.266) applies to a land-clearing crew's tasks and equip/train accordingly

Apply OSHA exposure guidance when handling fiberglass or mineral-wool insulation

Confirm the OSHA 1926.850 engineering survey is completed and documented before starting demolition operations

Classify trench soil per OSHA 1926 Subpart P (Type A/B/C) before selecting a protective system

Apply OSHA trench spoil-setback and ladder-egress requirements (29 CFR 1926.651)

Complete and retrieve an OSHA ITA submission (300A summary plus case data) via the API

Submit individual Form 300/301 injury and illness case records via the OSHA ITA API

submit osha injury and illness recordkeeping data (form 300a and related forms) through the injury tracking application api